Відео

What a gift you’ve providing UA-cam, but also to your son!!

Fantastic!

Save some wear and tear on your wrists - save time, and get a joist nailer - you’ll wonder how you worked without it.

Awesome process and work!! I love that you love your work and take pride in it.

why did you not start on the bottom corner?

Very creative.

What about finding the crown of all your studs before you build your wall?

Thank you 🙏 keep up the amazing work!

Did you hook those up in series or parallel?

What sealer did you use was the finish matte flat no shine

Why the insert on the bath at the end?

First mistake u never put an angle stop straight onto pex ! Always use a stub-out

parallel pliers are great for removing the staples

it's annoying how most electrical videos are in the usa where they build houses out of wood...

Would this meet code?

Very detailed. Thank you

What brand of epoxy are you using for your seems?

I am planning and about to do the same. I have an undercount sink too and thinking of how to change the sink in future? As the sink is sandwiched between the play wood and concrete?

No one knows that the tape housing itself is intended to be used as part of the measurement so that its accurate w/o bending, EVERY TAPE HAS THE HOUSING DIMEMSIONS TO ADD TO TAPE MEASUREMENT

Man Making Money= no unnecessary steps!!!!!!!!!

Painting them Gray?

Why would you tie in the recepticles to the lights ? At the switch then you are turning off power to the outlets when you turn off the lights ???

I thought most 3/8 nap will work

Awesome video. I was way over thinking it forgetting that I’m still mounting them to the wall… 🤦‍♂️

FYI for our European friends-the spacers are sold as fractions. Blame your Brit neighbors.

Loved your video

That was very bad workmanship. You really ruined that panel.

Thanks for ur guidance❤

Like here al de mexicanos k estan de chismosos!!

Thanks for wasting our time. Didn’t finish.

Commentary on what you are doing would have been nice. I could have watched paint dry and had the same level of interest.

Hey thanks for the idea man. i created a little modified version for cutting memory foam mattresses. This is a great diy solution for a straight cut. Much appreciated

I want to know what this looks like now since this video was made?

Did you run both drivers in your living room ceiling off of the same circuit? I have a large room with one switch 20amp breaker.

How many bags of 80lb concrete for the big foot footings? Thanks

Great video. I have a concrete countertop but I don't think it is solid concrete like yours. A huge chunk chipped off and it seems much thinner than what you have here. Also it's much lighter. I am now trying to repaint but cannot seem to find a way to match its existing paint... i'm not sure how it was painted. Is there anyting you would recommend if I just want to repaint the whole thing? Can I just use standard indoor/outdoor latex paint?

nice, very informative vid

a lot of sawder but nice man good job, I'm studying for skills USA. And I'm in the trade at diman regional and i just wanted to learn a few more steps and this really helped. Thanks man ,keep up the good work.

Curious, why go vertical with the strips and not horizontal, starting from the bottom up, letting each have the 2 inch overlay, water flows down, then you have no joints to fill in the corners and provides a better seal?

I dont know, but this is a simple and very effective cutting table. Thanks!

Thank you coach!!!! Finally a plumbers 101 teach vid that gets right down to even the minor details!!! Its all important!! God bless you sir!!

I can’t find part 3, any information about? Thanks

Looks fantastic, I hope yours doesn't crack like mine.

How do you think these would work in a 10ft ceiling in a garage? I’m caught between a really low profile led or wafer lights. For me, the brighter the better. Do these come in 8 inch or is 6 inch the largest they make for quick link? Thanks

Your video helped me make a decision at the store. Thank you

What are your thoughts on using exclusively moen or delta?

linseed oil is also used and should be cheaper

Funny how i was watching your videos about 7 years ago, i knew you as the person who panted all his tools grey. Took me awhile to find you again and I noticed you don’t pant your tools anymore😂. Thanks for providing your expertise helps us diy.

Dude ur awesome

Thanks Coach!